Digitech DL-8 Bedienungsanleitung

6nect the cable from the Input 1 (Mono) jack when not in use. If the optional Harman PS200R power supply is used, cables can remain connected.Input 2

7Foot Switch - Turns the effect on and off. The Foot Switch is also used for tapping in the delay time when using the Tap Tempo delay feature and for

8Tap Tempo DelayThe HardWire Delay/Looper’s Foot Switch can be used as a Tap Tempo switch for setting the delay time during a live performance. To acc

9the Indicator LED stops flashing and lights solid RED again. Once Tap Tempo mode is exited, the tapped delay time remains active until either the de

10Loop DelayThe Loop Delay type is used to create an infinite stereo delay loop up to 20 seconds long. Once a loop is created, you can add overdub par

11Switch is held down, indicating that anything played is being recorded and added to the loop.To stop the loop, quickly press the Foot Switch. This p

12Tails SwitchThe HardWire Delay/Looper features a switch that allows the delay repeats to continue being heard after the effect is bypassed. When the

13

14Amplifier SetupPS200R (optional)or

15Effects SetupNote: if the amp effects loop has a mix control, set the mix to 100% full wet.AMP RETURNAMP SENDPS200R(optional)

DECLARATION OF CONFORMITYManufacturer’s Name: DigiTechManufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USAdeclares that the produ

16Battery OperationIn the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need

17Switch is properly fastened, both Release Pins are flush with the outer side of the pedal.Foot SwitchPedal SwitchArmFoot SwitchRelease Pin9VDC Batte

18HardWire Performance AccessoriesThe performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories

19Hook-and-loop Pedalboard PadTo attach the Pedalboard Pad, do the following:Peel off the existing rubber skid pad from the bottom of the pedal.Peel t

20Foot Switch Glow StickerTo attach the Foot Switch Glow Sticker, do the following:Peel the adhesive backing from the Foot Switch Glow Sticker.Apply t

21StompLockTo place the StompLock over the pedal knobs, do the following:Set the knobs to your preferred setting.Gently push the StompLock over the to

22SpecificationsControls - Level, Repeats, Time, Type, On/Off PedalJacks - Input 1 (Mono), Input 2, Output 1 (Mono), Output 2Input Impedance - >1 M

23

8760 South Sandy ParkwaySandy, Utah 84070PH (801) 566-8800FAX (801) 566-7005 HardWire, StompLock, and DigiTech are trademarks of the Harman Music Grou

WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty:The warranty registration card must be mailed wit

1IntroductionMore than a remarkable achievement, HardWire™ represents a collection of significant improvements in effects pedals for guitar. HardWire

22 3 4 5678121189101

3What Does This Do?Level Knob - Controls the delay level. Turn this knob clockwise to increase and counter-clockwise to decrease the delay level. When

4range selected with the TYPE knob. The knob’s minimum position is the shortest delay time for the given range. The knob’s maximum position is the lon

5 ANALOG* - a vintage bucket brigade analog delay. SLAPBACK - 80 to 150 ms LO FI* - a low-fidelity delay that has limited bandwidth. TAPE* - a cla